New windows and doors improve comfort, cut energy bills and add long-term value to your home. Sightline Windows & Doors Cutler Bay pairs proven product lines with our own installing crews for lasting performance - and a price we put in writing.
1. Choose your installer
The unit is half the job - the install is the other half. Our own background-checked crews measure, set, seal and insulate every opening, and they know the lines we quote inside and out because they install them every week.
2. Select the right products
Compare styles, materials and glass packages side by side until the fit is right for your rooms, your budget and your goals. The product-line comparison below is the place to start.
3. Prepare your home for install
Before install day we walk you through a short checklist - furniture pulled back, treatments down, a clear path to each opening - so install day is watch-it-happen, not scramble.
Compare the Lines We Quote
Every project is priced on the same lines, side by side - the price indicators below are relative, and your consultant shows exact numbers on your actual openings.
PGTThe line Florida homeowners arrive naming - the most Miami-Dade certifications in the industry$$$
- More Miami-Dade NOA certifications than any other line we quote
- WinGuard, EnergyVue and ClassicVue Max systems built for every wind zone
- 99% on-time delivery keeps your install date on the calendar
CGIThe heavyweight impact line$$$$$
- Large-missile impact ratings for the strictest wind zones
- Architectural-grade aluminum with commercial-depth frames
- The line we quote when protection is the whole point
CWSThe Florida value pick$$
- Vinyl systems built in Florida for Florida codes
- Strong energy packages at the friendliest price point
- The smart start for whole-home replacements on a budget
ESWSlim lines, big glass$$$$
- Narrow-sightline aluminum for modern elevations
- Oversized openings and floor-to-ceiling glass
- Impact-rated without the bunker look
ECOThe aluminum impact workhorse$$$
- Miami-built aluminum impact systems
- A strong price-to-protection ratio for coastal homes
- Proven inventory lines with short lead times
CGI Sliding & Patio Doors: The Cutler Bay Owner’s Guide
We stock and install CGI-compatible sliding and patio door replacement parts and full door assemblies across Cutler Bay, with most common rollers, tracks, and handle sets available same-day and typical installed replacement costs running $340 to $780 depending on whether we’re swapping a roller carriage or the full panel. Most Cutler Bay homeowners discover the problem when the door starts catching at the sill during hurricane season, or when the lock no longer draws the panels tight enough to pass a pressure test. If the opening isn’t square, no amount of caulk makes it right.
Which CGI Models This Applies To
CGI’s sliding and patio door lineup breaks into three series that matter for parts matching: the Estate Series (ES) with its heavier 2-1/4 inch frame depth, the Sentinel Series with the slim-profile 1-3/4 inch frame, and the commercial-grade Targa Series with reinforced corner construction. The roller assemblies are not interchangeable between these frame depths, a compatibility gotcha we’ve seen trip up online orders more than once. Model numbers are stamped on the hinge jamb label or etched into the glass corner, usually formatted as ES-SPD-XXXX or SE-SPD-XXXX for Sentinel.
For rollers and tracks, we stock both OEM CGI parts and quality aftermarket equivalents from C.R. Laurence and Prime-Line. The OEM roller (CGI part 2200-series) uses a stainless steel axle rated for 150 lb per panel; the aftermarket equivalent we carry matches that spec at roughly 60 percent of the part cost. We specify by what the opening requires, not by what is in stock. Sightline Windows & Doors Cutler Bay is an independent service provider, not affiliated with CGI.
Before
AfterSigns Your CGI Sliding & Patio Door Is Failing
- The door sticks or skips at the sill. This usually means the roller carriage has flattened or the axle has corroded. In Cutler Bay, we regularly see this within 6 to 8 years on coastal-facing units because salt air accelerates bearing wear faster than most product sheets admit.
- The lock thumbturn spins without engaging the deadbolt. The internal cam has sheared or the mortise mechanism has slipped out of alignment. On CGI’s multi-point systems, this often starts at the top latch and works downward.
- Daylight shows between the panel and the jamb when closed. The panel has dropped on worn rollers, or the adjustable strike has settled. Either way, the seal is compromised and the door will not hold against wind-driven rain.
- The track is grooved or dented at the primary wear point. Steel rollers running on an aluminum track eventually eat a channel into the metal. Once the track is scored, new rollers will fail prematurely until the track is replaced or sleeved.
- Condensation appears between the glass lites. The insulated glass unit (IGU) seal has failed. This is not a roller or hardware issue, but Cutler Bay homeowners often notice it while inspecting other door problems. The IGU must be replaced as a sealed assembly, not repaired in place.
Replacement Cost & What’s Included
| Component | Part + Labor Range | Notes |
|---|---|---|
| Roller carriage (single panel) | $180 - $290 | OEM or matched aftermarket; includes sill cleaning and track inspection |
| Full track replacement | $340 - $520 | Aluminum extrusion, cut to opening; more if subfloor is rotted |
| Multi-point lock mechanism | $260 - $410 | Handle set, mortise box, and strike alignment |
| Full panel replacement (impact-rated) | $1,800 - $2,900 | Measured survey, removal, disposal, new panel, seal and trim |
| IGU replacement (dual-pane) | $340 - $580 | Measured to 1/16 inch; tempered glass adds 20-30% |
What drives the range: frame condition (aluminum corrosion is common in Cutler Bay’s coastal humidity), whether the rough opening needs shimming, and whether the replacement requires a permit pull. We pull permits when the job crosses into structural modification; the permit cost is listed as a line item on the written quote, not buried in overhead. Every engagement begins with a measured survey the customer keeps, and the written quote cannot differ from that document. The work is covered by our 365-Day Done Right Promise, written into the Haven Standard.
DIY or Call Us?
An owner can safely check three things: whether debris is packed in the track (vacuum it out), whether the lock thumbturn operates smoothly, and whether the panel lift holes are accessible without removing trim. Beyond that, sliding door panels are heavy, often 80 to 120 pounds for impact-rated CGI units, and the roller adjustment screws sit under spring tension. We’ve seen homeowners strip the adjustment hex or drop a panel trying to free a seized carriage.
If you need the part identified, measured, and matched to your CGI series, call (786) 886-1945. We bring the measured survey, the written price, and the correct parts on the first visit. Haven Clause 1 is the whole point.
FAQs
In Cutler Bay’s coastal environment, expect 6 to 10 years on standard rollers and 10 to 14 on stainless steel OEM units if the track is kept clean. Salt air and humidity degrade aluminum frames faster than most product sheets admit, which is why we inspect the track every time we replace rollers. Call (786) 886-1945 for an exact quote - estimates are free.
Sometimes. If the issue is a loose set screw or a misaligned strike plate, adjustment takes ten minutes. If the mortise mechanism internals have failed, replacement is the only reliable fix; we’ve never seen a temporary repair on a CGI multi-point lock hold past the next storm season. Call (786) 886-1945 for an exact quote - estimates are free.
Most CGI sliding door panel replacements in Cutler Bay are completed in one day, assuming the rough opening is sound and the trim package is standard. If we find rot or out-of-square conditions during the measured survey, we’ll document it with photos and revise the written scope before any work starts. Call (786) 886-1945 for an exact quote - estimates are free.
We carry the four most common failure parts for CGI sliding and patio doors: 2200-series roller carriages in both frame depths, multi-point mortise mechanisms for Estate and Sentinel series, standard and keyed handle sets, and track replacement extrusions cut to common widths. Less common Targa Series hardware is available next-day. Call (786) 886-1945 for an exact quote - estimates are free.
Ready to get your CGI sliding or patio door working right? Call (786) 886-1945 to schedule your free estimate. We’ll bring the measured survey, the written price, and the documentation you need to make the decision on your own timeline. All technicians are background-checked, uniformed, and identified by license number before arrival. Every completed job leaves a documented photo record and is covered by the 365-Day Done Right Promise under the Haven Standard.
Written by Sonia Raman, Owner, Sightline Windows & Doors Cutler Bay at Sightline Windows & Doors Cutler Bay, serving Cutler Bay and nearby areas.
Six Reasons Homeowners Choose Sightline Windows & Doors Cutler Bay
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.
Other Sightline Windows & Doors Cutler Bay Services
