CGI Door Installation Nationwide | Sightline Windows & Doors Cutler Bay

CGI Door Installation: The Cutler Bay Owner’s Guide

CGI door installation in Cutler Bay typically runs $1,800 to $4,200 for a standard single entry unit, depending on series, impact rating, and whether the rough opening needs reframing. We stock CGI hardware and frame components for same-day starts on most common series, and every quote is written before any work begins. Most Cutler Bay homeowners discover their CGI door needs attention when the multipoint lock stops engaging smoothly, the sweep gaps let water pool on the tile during summer storms, or they notice daylight between the frame and the jamb after years of frame settling in our coral-gables soil.

Call (786) 886-1945

Which CGI Models This Applies To

We install and replace across CGI’s full residential door lineup, including the Estate Series, Sentinel Series, and the commercial-grade Sentinel HC line that shows up frequently in Cutler Bay’s newer construction near Old Cutler Road. The label you’re looking for is inside the hinge jamb, a stamped metal tag with the series code, nominal size, and Miami-Dade NOA number. Match that tag exactly, CGI changed frame depths between 2018 and 2021 on several Estate configurations, and the wrong subframe will not seat.

For hardware specifically, the multipoint locking systems differ between series. Estate uses a two-point with an auxiliary deadbolt; Sentinel carries a three-point with shootbolts top and bottom. We stock both OEM assemblies and tested equivalents from Truth Hardware and Hoppe that meet the same cycle ratings. The aftermarket route saves roughly $140 to $220 on parts, but we only spec it when the warranty and cycle count match the original. If your tag reads “CGI-WD-” followed by a four-digit code, you’re in the post-2019 frame family and need the deeper subframe. We check this on every site walk, because ordering the wrong frame costs a week in Cutler Bay’s current permit cycle.

Before

After

Signs Your CGI Door Installation Is Failing

• The multipoint lock requires shoulder pressure to engage. The locking points have drifted out of alignment with the keepers, usually from frame racking in our humid, salt-air environment. The mechanism itself is often fine; the frame has settled or the hinge screws have backed out from thermal cycling.
• Water pools on the interior side after a hard rain. The sill cap seal has compressed or theweep holes are clogged with Cutler Bay’s fine coral dust. On units facing Biscayne Bay directly, we’ve seen aluminum sills corrode through in under eight years despite the anodized finish.
• Daylight visible around the frame perimeter. The installation foam has degraded or the frame was never properly shimmed against the rough opening. This is the symptom Sonia watches for most carefully, a gap that size means the impact rating is compromised and the door will not perform in a rated wind event.
• The door drags or sticks seasonally. Aluminum expands roughly 1/8 inch per 10 feet of frame between our coolest January mornings and August afternoon sun. If the clearance was set tight during a cool month, summer binding is guaranteed. We set clearance at mid-range temperature to split the difference.
• Glass fogs between the panes on an insulated unit. The edge seal has failed, admitting moisture into the air gap. For impact-rated glass, this is not a field repair, the entire IG unit must be re-manufactured to maintain the NOA. We measure the visible glass, the overall unit size, and the spacer color to order the correct replacement.

Replacement Cost & What’s Included

What drives the range: the series and size of the door, whether the existing frame can be reused, and whether the rough opening is plumb and square. If the opening isn’t square, no amount of caulk makes it right, reframing is the honest fix and we say so in the written scope. Every price includes the measured survey you keep, the CGI unit or component, installation per manufacturer spec, permit pull if required, and our 365-Day Done Right Promise under the Haven Standard. The written quote and the final invoice are the same document, Haven Clause 1, no change orders unless you add scope.

DIY or Call Us?

What you can safely check: the hinge screws for tightness, the sweep for visible damage, and the weep holes for obstruction with a thin wire. These are maintenance items, not repairs.

Where DIY goes wrong: removing a CGI impact-rated door without supporting the frame risks racking the opening and voiding the NOA. The multipoint lock is under spring tension and the alignment is finicky, a millimeter off and the shootbolts won’t seat. Impact glass units weigh 80 to 140 pounds depending on size and require two people with suction cups and proper edge protection. We’ve been called to three Cutler Bay jobs in the past two years where a homeowner cracked a replacement IG unit during handling, turning a $580 hardware call into a $1,400 glass reorder.

We’re an independent service provider, not affiliated with CGI. We install their products because the specifications hold up in South Florida’s conditions, and we stock what fails most often. If you’re unsure whether the issue is the door, the frame, or the installation, call (786) 886-1945. We’ll schedule a site walk, measure the opening, and hand you a written price before any work starts.

FAQs